Manufactured from 77mm filled aluminium slats.
This made to measure remote controlled electric door is a versatile multi-purpose product, which can be fitted in three different ways to suit your garage:
Can be fitted on the back of the brick piers.
Can be fitted between the brick piers.
Can be fitted infront of the piers.
The popular and recommended installation method with the guides and roller box fitted behind the brick piers/rear of lintel. Maximum garage entrance width achieved. Very easy installation method with neat appearance. No guides or box visible when viewed from the front.
Guides fitted between the piers, box enclosure fitted under the lintel. Reduces entrance width and height, but maximizes garage length. Guides and box can be powder coated to match curtain.
Box and guides fitted onto the front of the brickwork. Maximizes entrance width, height and garage length.
Available from 4ft wide to approximately 18ft wide (including guide channels) and upto 12ft high. Full powder coated aluminium box enclosure to the roll included as standard. Complete with two hand transmitters, bottom edge safety device and high quality control box with courtesy light and up/down control button. Available in numerous standard colours and wood effect foil laminate finishes all on short lead times.
Ideal for garages, home gyms and workshops, pottery rooms, games rooms and garages with four-post lifts.
5 year guarantee on the tubular motor (fitted Left Hand side or Right Hand side to customer’s choice)
10 year guarantee on the slats.
Measuring for your Aluroll insulated roller door.
The ordering WIDTH of an Aluroll door is the total width including the guides.
Guide channels are 90mm wide as standard, or 70mm on request at no extra cost.
The ordering HEIGHT of an Aluroll door is the total height including the roller box enclosure.
Roller box enclosure is 300mm square on doors upto 3000mm high.
Doors over 3000mm high have a 360mm square roller box enclosure.
The Aluroll roller door can be fitted in the following ways.
Fitting on back of opening (recommended method).
Space available on the back of the piers should be wide enough to accommodate the guide channels.
Headroom from bottom of lintel to lowest point of ceiling is ideally 300mm or more to accommodate the whole of the box enclosure.
The Headroom of less than 300mm is not a problem, as any of the exposed face of the powder coated aluminium box enclosure that shows below the lintel acts as a neat facia.
Tip: If the reveals are too narrow to accommodate all of the guides, upto about 30mm of the guides can show into the opening. Check that the back of the brick piers and the back of the lintel make a flat continuous surface to offer the guides and box onto.
Fitting in between brickwork and under the lintel.
Measure dimensions 1 and 2 shown in the above measure up form very accurately. Allowing for only run out in the brick piers and any run out in the floor or lintel, take the tightest sizes.
Tip: Order your door 10mm narrower and 5mm to 10mm smaller than these tight sizes.
External fit.
When fitting flat onto the front of the opening a flat continuous fixing surface is required for the box and guides to fit onto.
N.B. All roller doors can show marking on the back of the top 5 or 6 slats over time where the slats roll onto the shaft rings. These would be visible and do not constitute a warranty claim.
Tip: The “back” of the shutter curtain is seen with this external fit method. Foil Laminated Woodgrain slats are not laminated on the back of the slats so are not suitable for this external fit method of installation. Any other colour slats have same colour on the back.
Installation instructions for DIY installation by customer:
Estimated lead time on Aluroll insulated roller garage doors
1-3 weeks, all roller doors are made to measure
At the point of delivery an able-bodied male must be present to assist the driver in offloading the door.
Every effort is made to deliver goods by the estimated delivery dates given. Due to constantly changing stock levels at the manufacturers, production processes and delivery logistics any delivery or installation dates given are approximate only and the Company accepts no liability for any such delay. We endeavor to deliver all our garage doors and products as fast and efficient as possible. Most of our doors are not off the shelf they are made to order.
Aluroll Classic Insulated Roller Garage Door.
Manufactured from 77mm filled aluminium slats.
This made to measure remote controlled electric door is a versatile multi-purpose product, which can be fitted in three different ways to suit your garage:
Can be fitted on the back of the brick piers.
Can be fitted between the brick piers.
Can be fitted infront of the piers.
The popular and recommended installation method with the guides and roller box fitted behind the brick piers/rear of lintel. Maximum garage entrance width achieved. Very easy installation method with neat appearance. No guides or box visible when viewed from the front.
Guides fitted between the piers, box enclosure fitted under the lintel. Reduces entrance width and height, but maximizes garage length. Guides and box can be powder coated to match curtain.
Box and guides fitted onto the front of the brickwork. Maximizes entrance width, height and garage length.
Available from 4ft wide to approximately 18ft wide (including guide channels) and upto 12ft high. Full powder coated aluminium box enclosure to the roll included as standard. Complete with two hand transmitters, bottom edge safety device and high quality control box with courtesy light and up/down control button. Available in numerous standard colours and wood effect foil laminate finishes all on short lead times.
Ideal for garages, home gyms and workshops, pottery rooms, games rooms and garages with four-post lifts.
5 year guarantee on the tubular motor (fitted Left Hand side or Right Hand side to customer’s choice)
